THE FUNDAMENTALS OF PLUMBING SKILLS FOR BATHTUB INSTALLATION

The Fundamentals of Plumbing Skills for Bathtub Installation

The Fundamentals of Plumbing Skills for Bathtub Installation

Blog Article

Click Here!

Were you trying to find facts and techniques on Installing A Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Mounting a bathtub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately tough job. If the old bathtub is readily accessible, the job can relocate speedily; if you have to open up a wall surface to remove the old tub as well as place the new tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the task as well as fit attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to take into consideration employing one prior to you start. Chances are you might need a professional plumber to make tube connections.
This article will certainly assist you mount a new tub in your shower room if you have already bought a new bathtub and also don't need to alter the arrangement of your previous water pipes.
Your tools and material list need to comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Planning for the Setup


    Firstly, the sustaining structure supplied with the bathroom must be fitted (if needed) according to the producer's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop strain on the tub.
    Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be suited its last setting.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is frequently the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
    Prior to moving on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Installing the Bath tub


    Utilizing both wood boards under its feet, position the tub in the called for position. The wooden boards are handy in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
    The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub till the level reviews level.
    To install faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if required. Load the tub and additionally check the overflow outlet as well as the regular outlet for leaks.
    Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait up until the tub has actually been made use of at the very least when as this will resolve it right into its final position.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Safeguard the tap in position with the producer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former type must be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the location where the bath satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall between the bath and the tiling, bring about problems with moisture as well as feasible leakages to the ceiling below.
    You can pick from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can break rather early if you do not consider this activity prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is recommended to fit the floor tiles using waterproof or water resistant sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    I was guided to that article about How to Install a Bathtub Yourself through an associate on our other web property. In case you appreciated our blog post if you please don't forget to pass it around. Thanks a bunch for your time. Come back soon.


    Search-end for emergency plumbing.

    Report this page